View MIC38HC42YM_4173966.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MIC38HC42/3/4/5
Micrel, Inc.
MIC38HC42/3/4/5
BiCMOS 1A Current-Mode PWM Controllers
General Description
The MIC38HC4x family are fixed frequency current-mode PWM controllers with 1A drive current capability. Micrel's BiCMOS devices are pin-compatible with 384x bipolar devices. Their high output drive, with fast rise and fall times, combined with low startup current make it an ideal PWM controller where high efficiency is required. Undervoltage lockout circuitry allows the '42 and '44 versions to start up at 14.5V and operate down to 9V, and the '43 and '45 versions start at 8.4V with operation down to 7.6V. All versions operate up to 20V. When compared to bipolar UC384x devices operating from a 15V supply, start-up current has been reduced to 50A typical and operating current has been reduced to 4.0 mA typical. Decreased output rise and fall times drive larger MOSFETs, and rail-to-rail output capability increases efficiency, especially at lower supply voltages. The MIC38HC4x also features a trimmed oscillator discharge current and bandgap reference. MIC38HC4x-1 is available in 14-pin plastic DIP and SOIC packages. 8-pin devices feature small size, while 14-pin devices separate the analog and power connections for improved performance and power dissipation.
Features
* Fast 20ns output rise and 15ns output fall times * -40C to +85C temperature range exceeds UC284x specifications * High-performance, low-power BiCMOS Process * Ultralow start-up current (50A typical) * Low operating current (4mA typical) * High output drive (1A peak current, HC version) * CMOS outputs with rail-to-rail swing * Current-mode operation up to 500kHz * Trimmed 5V bandgap reference * Pin-for-pin compatible with UC3842/3843/3844/3845(A) * Trimmed oscillator discharge current * UVLO with hysteresis * Low cross-conduction currents
Applications
* * * * * * * Current-mode, off-line, switched-mode power supplies Current-mode, dc-to-dc converters. Step-down "buck" regulators Step-up "boost" regulators Flyback, isolated regulators Forward converters Synchronous FET converters
Functional Diagram
VDD
7 (12)
* 35V 5V Reference UVLO
VREF
8 (14)
(VD)
(11)
RT/CT
4 (7)
Oscillator T Q
OUT
6 (10)
FB
2 (3)
2R 2.5V R S R Q
(PGND)
(8)
* COMP
1 (1)
GND*(AGND)
5 (9)
ISNS
3 (5)
( ) pins are on MIC38HC4x-1 (14-lead) versions only * MIC38HC4x (8-lead) versions only MIC38HC42, MIC38HC43 (96% max. duty cycle) versions only MIC38HC44, MIC38HC45 (50% max. duty cycle) versions only
Micrel, Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel + 1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com
April 2005
1
M9999-042205
MIC38HC42/3/4/5
Micrel, Inc.
Ordering Information
Standard Part Number Pb-Free MIC38HC42YN MIC38HC43YN MIC38HC44YN MIC38HC45YN Contact Factory Contact Factory Contact Factory Contact Factory MIC38HC42YM MIC38HC43YM MIC38HC44YM MIC38HC45YM MIC38HC42-1YM MIC38HC43-1YM MIC38HC44-1YM MIC38HC45-1YM Junction Temp. Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C Package 8-pin Plastic DIP 8-pin Plastic DIP 8-pin Plastic DIP 8-pin Plastic DIP 14-pin Plastic DIP 14-pin Plastic DIP 14-pin Plastic DIP 14-pin Plastic DIP 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 14-pin SOIC 14-pin SOIC 14-pin SOIC 14-pin SOIC
MIC38HC42BN MIC38HC43BN MIC38HC44BN MIC38HC45BN MIC38HC42-1BN MIC38HC43-1BN MIC38HC44-1BN MIC38HC45-1BN MIC38HC42BM MIC38HC43BM MIC38HC44BM MIC38HC45BM MIC38HC42-1BM MIC38HC43-1BM MIC38HC44-1BM MIC38HC45-1BM
Selection Guide
UVLO Thresholds Duty Cycle 0% to 96% 0% to 50% Startup 8.4V Minimum Operating 7.6V MIC38HC43 MIC38HC45 Startup 14.5V Minimum Operating 9V MIC38HC42 MIC38HC44
M9999-042205
2
April 2005
MIC38HC42/3/4/5
Micrel, Inc.
Pin Configuration
MIC38HC4x-1
COMP 1 NC 2 FB 3 14 VREF 13 NC 12 VDD 11 VD 10 OUT 9 AGND 8 PGND
MIC38HC4x
COMP 1 FB 2 ISNS 3 RT/CT 4 8 7 6 5 VREF VDD OUT GND
NC 4 ISNS 5 NC 6 RT/CT 7
8-Pin DIP (N) 8-Lead SOIC (M)
14-Pin DIP (-1BN) 14-Lead SOIC (-1BM)
Pin Description
Pin Number N, M, MM 1 Pin Number -1BN, -1BM 1 2 2 3 4 3 5 6 4 5 8 9 6 10 11 7 12 13 8 14 7 Pin Name COMP NC FB NC ISNS NC RT/CT GND PGND AGND OUT VD VDD NC VREF Pin Function Compensation: Connect external compensation network to modify the error amplifier output. Not internally connected. Feedback (Input): Error amplifier input. Feedback is 2.5V at desired output voltage. Not internally connected. Current Sense (Input): Current sense comparator input. Connect to current sensing resistor or current transformer. Not internally connected. Timing Resistor/Timing Capacitor: Connect external RC network to select switching frequency. Ground: Combined analog and power ground. Power Ground: N-channel driver transistor ground. Analog Ground: Controller circuitry ground. Power Output: Totem-pole output. Power Supply (Input): P-channel driver transistor supply input. Return to power ground (PGND). Analog Supply (Input): Controller circuitry supply input. Return to analog ground (AGND). Not internally connected. 5V Reference (Output): Connect external RC network.
April 2005
3
M9999-042205
MIC38HC42/3/4/5
Micrel, Inc.
Absolute Maximum Ratings
Zener Current (VDD) ................................................... 30mA Operation at 18V may require special precautions (Note 6). Supply Voltage (VDD), Note 6 ....................................... 20V Switch Supply Voltage (VD) .......................................... 20V Current Sense Voltage (VISNS) ..................... -0.3V to 5.5V Feedback Voltage (VFB) ................................ -0.3V to 5.5V Output Current, 38HC42/3/4/5 (IOUT) .............................. 1A Operating Junction Temperature (TJ) ....................... 150C Package Thermal Resistance 8-Pin Plastic DIP (JA) ....................................... 125C/W 8-Pin MM8TM (JA) ............................................. 250C/W 8-Pin SOIC (JA) ............................................... 170C/W 14-Pin Plastic DIP (JA) ....................................... 90C/W 14-Pin SOIC (JA) ............................................. 145C/W Storage Temperature (TA) ....................... -65C to +150C
Electrical Characteristics
VDD = 15V, Note 4; RT = 9.09k; CT = 3.3nF; -40C TA 85C; unless noted Parameter Reference Section Output Voltage Line Regulation Load Regulation Temp. Stability Total Output Variation Output Noise Voltage Long Term Stability Output Short Circuit Oscillator Section Initial Accuracy Voltage Stability Temp. Stability Clock Ramp Reset Current Amplitude Error Amp Section Input Voltage Input Bias Current AVOL Unity Gain Bandwidth PSRR Output Sink Current Output Source Current VOUT High VOUT Low VCOMP = 2.5V VFB = 5.0V 2 VO 4V Note 1 12 VDD 18V VFB = 2.7V, VCOMP = 1.1V VFB = 2.3V, VCOMP = 5V VFB = 2.3V, RL = 15k to ground VFB = 2.7V, RL = 15k to VREF 65 0.7 60 2 -0.5 5 14 -1 6.8 0.1 1.1 2.42 2.50 -0.1 90 1.0 2.58 -2 V A dB MHz dB mA mA V V TA = 25C, Note 5 12 VDD 18V, Note 6 TMIN TA TMAX, Note 1 TA = 25C, VRT/CT = 2V TA = TMIN to TMAX VRT/CT peak to peak 7.7 7.2 49 52 0.2 0.04 8.4 8.4 1.9 9.0 9.5 55 1.0 kHz % %/C mA mA Vp-p TA = 25C, IO = 1mA 12V VDD 18V, IO = 5A, Note 6 1 IO 20mA Note 1 Line, Load, Temp., Note 1 10Hz f 10kHz, TA = 25C, Note 1 TA = 125C, 1000 hrs., Note 1 -30 4.82 50 5 -80 25 -180 4.90 5.00 2 1 0.2 5.18 5.10 20 25 V mV mV mV/C V V mV mA Test Conditions Min Typ Max Units
M9999-042205
4
April 2005
MIC38HC42/3/4/5
Parameter Current Sense Gain MaximumThreshold PSRR Input Bias Current Delay to Output Output RDS(ON) `HC' High RDS(ON) `HC' Low Rise Time Fall Time Undervoltage Lockout Start Threshold MIC38HC42/4 MIC38HC43/5 Minimum Operating Voltage MIC38HC42/4 MIC38HC43/5 Pulse Width Modulator Maximum Duty Cycle MIC38HC42/3 MIC38HC44/5 Minimum Duty Cycle Total Standby Current Start-Up Current VDD = 13V, 38HC42/44 VDD = 7.5V, 38HC43/45 VFB = VISNS = 0V IDD = 25mA, Note 6 30 50 94 46 96 50 13.5 7.8 8 7.0 14.5 8.4 9 7.6 ISOURCE = 200mA ISINK = 200mA TA = 25C, CL = 1nF TA = 25C, CL = 1nF 10 5.5 20 15 Notes 2, 3 VCOMP = 5V, Note 2 12 VDD 18V, Note 2 2.85 0.9 3.0 1 70 -0.1 120 Test Conditions Min Typ
Micrel, Inc.
Max Units
3.15 1.1
V/V V dB
-2 250
A ns
50 40 ns ns
15.5 9.0 10 8.2
V V V V
% % 0 %
200
A mA V
Operating Supply Current Zener Voltage (VDD)
4.0 37
6.0
Note 1: These parameters, although guaranteed, are not 100% tested in production. Note 2: Parameter measured at trip point of latch with VEA = 0. Note 3: Gain defined as: A= VPIN1 ; 0 VTH (ISNS ) 0.8V VTH (ISNS )
Note 4: Adjust VDD above the start threshold before setting at 15V. Note 5: Output frequency equals oscillator frequency for the MIC38HC42 and MIC38HC43. Output frequency for the MIC38HC44, and MIC38HC45 equals one half the oscillator frequency. Note 6: On 8-pin version, 20V is maximum input on pin 7, as this is also the supply pin for the output stage. On 14-pin version, 40V is maximum for pin 12 and 20V maximum for pin 11.
April 2005
5
M9999-042205
MIC38HC42/3/4/5
Micrel, Inc.
Typical Characteristics
Oscillator Frequency Configuration
100
OUTPUT DEAD TIME (%)
100 200pF 470pF 1nF 1.8nF VDD = 15V
OSC. DISCHARGE CURRENT (mA)
MIC38C/HC42/43 Output Dead Time vs. Oscillator Frequency
Oscillator Discharge Current vs. Temperature
9.0 8.8 8.6 8.4 8.2 8.0 7.8 7.6 7.4 VDD = 15V VOSC = 2V 7.2 7.0 -60 -30 0 30 60 90 120 150 TEMPERATURE (C)
RT RESISTANCE (k)
4.7nF 10 10nF 200pF 470pF 1nF 18nF 1 1x104 1x105 FREQUENCY (Hz) 1x106
10 4.7nF 10nF VDD = 15V
1 1x104 1x105 1x106 OSCILLATOR FREQUENCY (Hz)
CURRENT SENSE AMP THRESHOLD (V)
1.2 1.0 125C 0.8 0.6 25C 0.4 0.2 0.0 -50C
VREF SHORT CURCUIT CURRENT (mA)
Current Sense Amplifier vs. Error Amplifier Output
Short-Circuit Reference Current vs. Temperature
120 OUTPUT VOLTAGE (V) 100 80 60 40 20 VDD = 15V 25 20 15 10 5 0 -5 -10 -15 0.0
MIC38C4x Output Waveform
VD = 15V CL = 1nF 0.2 0.4 0.6 TIME (s) 0.8 1.0
0 2 4 6 8 ERROR AMPLIFIER OUTPUT (V)
0 -60 -30 0 30 60 90 120 150 TEMPERATURE (C)
M9999-042205
6
April 2005
MIC38HC42/3/4/5
Micrel, Inc.
Package Information
PIN 1 DIMENSIONS: INCH (MM)
0.380 (9.65) 0.370 (9.40)
0.135 (3.43) 0.125 (3.18)
0.255 (6.48) 0.245 (6.22) 0.300 (7.62)
0.013 (0.330) 0.010 (0.254) 0.018 (0.57) 0.100 (2.54) 0.130 (3.30) 0.0375 (0.952) 0.380 (9.65) 0.320 (8.13)
8-Pin Plastic DIP (N)
.770 (19.558) MAX PIN 1
.235 (5.969) .215 (5.461)
.060 (1.524) .045 (1.143) .160 MAX (4.064) .310 (7.874) .280 (7.112) .080 (1.524) .015 (0.381)
.015 (0.381) .008 (0.2032) .160 (4.064) .100 (2.540) .110 (2.794) .090 (2.296) .060 (1.524) .045 (1.143) .023 (.5842) .015 (.3810) .400 (10.180) .330 (8.362)
14-Pin Plastic DIP (N)
April 2005
7
M9999-042205
MIC38HC42/3/4/5
Micrel, Inc.
0.026 (0.65) MAX)
PIN 1
0.157 (3.99) 0.150 (3.81)
DIMENSIONS: INCHES (MM)
0.050 (1.27) TYP
0.020 (0.51) 0.013 (0.33) 0.0098 (0.249) 0.0040 (0.102) 0-8 SEATING PLANE 45 0.010 (0.25) 0.007 (0.18)
0.064 (1.63) 0.045 (1.14)
0.197 (5.0) 0.189 (4.8)
0.050 (1.27) 0.016 (0.40) 0.244 (6.20) 0.228 (5.79)
8-Pin SOIC (M)
PIN 1
0.154 (3.90)
DIMENSIONS: INCHES (MM)
0.026 (0.65) MAX)
0.050 (1.27) 0.016 (0.40) TYP TYP 0.006 (0.15)
0.193 (4.90) 45 3-6 0.244 (6.20) 0.228 (5.80)
0.057 (1.45) 0.049 (1.25)
0.344 (8.75) 0.337 (8.55)
SEATING PLANE
14-Pin SOIC (M)
MICREL INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL
+ 1 (408) 944-0800
FAX
+ 1 (408) 474-1000
WEB
http://www.micrel.com
This information furnished by Micrel in this data sheet is believed to be accurate and reliable. However no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2000 Micrel Incorporated
M9999-042205
8
April 2005

▲Up To Search▲

Price & Availability of MIC38HC42YM

	To Download MIC38HC42YM Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .